Reference 13-4 July 2012 pg.4 of 8Copyright 2012 Monster Tower, Inc.
Attach Bases to the Legs
5A
Forward Folding Instructions - Option A (Recommended)
Large portion of Base
toward back of boat
Quick
Release Knob
at Back
M12 x 35
Pivot Bolt
at Front
Attach all bases to the legs using the M12 x 35 bolt and the Quick Release
Knob. Run bolt and knob through the Heim Joint into the Swivels. Hand tighten.
Bases will now pivot and swivel on the Heim Joints. Loosen the jam nut on the
Heim Joint so the base will pivot along side of the boat (parallel to the boat center).
IMPORTANT: Large portion of bases should face toward the back of the boat to
ensure that the legs do not contact the bases when tower is folded.
The base swivel can be mounted with the M12 x 35 bolt either toward the inside
or outside of the boat. For easiest access, we recommend mounting the bolt head
toward the outside. Position the tower “Face Down” over the taped area on the deck. Pivot the tower upright to assure there is
ample clearance with the windshield (and Bimini if you will add one). Adjust location if needed. You may want to try a few
mounting spots to make sure you have the best possible location for the tower when folded down. It is important to look under
the deck where all four bases will mount to make sure there are no wires or other obstructions, and to make sure there is a at
surface for the base plates. Many boats have foam oatation under the deck that must be removed to mount the Below Deck
plates. Also, avoid stringers and wiring channels when determining base locations.
6A
With the tower upright, position the FRONT BASES to have maximum contact with the deck. Hand tighten the swivel to the bases
and the jam nut on the Heim so the footing remains stable on the deck. Adjust the width of the legs at the top section to achieve
maximum contact. After you are sure of the location of the FRONT BASES, mark the locations on the tape.
IMPORTANT: Double check the distance from the back of each base to the rear of the boat (or other reference point) to make sure
they are positioned in the same location on each side of the boat. This assures the tower will pivot smoothly front to back.
Locate the bases on the deck.
7A
Attach the FRONT BASES to the boat.
Detach the Front bases from the legs and take them apart for mounting. IMPORTANT: To assure correct distance between front and
back bases, you will rst attach only the front bases to the boat. Make sure the large end of the base is toward the back of the boat.
Go to the section - “Attaching Bases to the Deck of the Boat”.
8A
Locate and Attach the Front Legs to the deck.
After bolting front bases to the deck,
re-assemble both front swivels on
bases. Using the M12 x 85 bolt,
washers and Nylock Nut. Using
M12x35 attach the swivel to
the Heim on the tower. Hand
tighten so the swivels stay
in position.
M12 x 85 Bolt
M12 x 35 Bolt
Boat
Return from “Attaching Bases to the Deck of the Boat”
9A
Check Back Bases & Quick Release Knob
Back Bases should still be attached
from step 5A. Pivot tower upright
so the base contacts the boat.
Position the bases to sit at as
possible on the boat. Hand tighten
the swivels. Mark the base location
on the tape.
Quick Release Knob
10A
Double check Location and Attach both Back Bases to the boat.
Pivot the tower a few times making sure the Back bases have good contact with the deck. Mark any
location dierences and adjust as necessary. Detach only the back bases from the swivels and take Back
base assemblies apart for mounting. Leave Front Bases attached. When attaching the bases, make sure
the large portion of the base is toward the back of the boat.
Go to the section - “Attaching Bases to the Deck of the Boat”.
Return from “Attaching Bases to the Deck of the Boat”
11A
Re-assemble both Back Bases to the boat.
After bolting the back bases onto the boat, re-assemble back bases as shown in step 9A. Pivot the tower upright and secure the
tower by using the Quick Release Knob. Run it through the Heim into the swivel. The tower now stands by itself.
Go to STEP 12 - “IMPORTANT - Final Adjustments and Locking”.
Attach lanyard from
Quick Release Knob
to the M12x85 bolt
Hand
Tighten